Error e1 on the triumph treadmill. Typical errors in track operation

Troubleshoot tape problems. Determine whether the problem is with the tape itself or with the mechanism itself that moves the tape.

• Determining this will help you in the next step. If the problem is with the tape itself, you can fix it yourself relatively easily. But engine or mechanical problems can become more difficult to solve at home.

Turn off your treadmill. When you are repairing your treadmill, it is very important to remember to turn it off, as it could accidentally turn on and injure you.

Clean the surface of the track belt. Apply cleaner to the towel and wipe the tape. Dirt and dust can accumulate on the belt, which can slow it down. Debris from the belt can also get inside the treadmill, causing mechanical problems.

• Start cleaning at the top of the tape and pull it firmly to move it down until you have cleaned the entire surface.
• Make sure the coating is dry before using the track. You may slip and injure yourself on a wet belt.

Place the treadmill belt in the center. Adjust the belt so that it is centered on the mechanism. The bands may stretch and begin to move to one side after frequent use. You can try to shift the belt on the treadmill by pulling it slightly away from the side it leans towards.

• If the problem is serious, then it should be addressed by a technician.

Lubricate the tape. If your treadmill belt temporarily stops when you step on it, you may need to lubricate it. This reduces friction and can extend the life of the belt.

• Buy treadmill belt lubricant or any silicone lubricant. Spray a thin layer of it between the belt and the treadmill deck. For more complete information how to lubricate the flooring, you can refer to the corresponding article.

Check the speed sensor. The speed sensor helps move the belt. If the belt jerks or does not increase speed, the sensor may be dirty or disconnected.

• Typically the sensor is located inside the treadmill, next to the belt. Consult your owner's manual to find out exactly where the sensor is located in your machine.

Replace the ribbon. If the previous steps did not solve the problem you are having with your ribbon, you may need to replace it. Order a replacement from the manufacturer if you want to do this yourself. Make sure it will be the right model for your driveway.

• You can take your treadmill to a professional repair technician to have the belt replaced.

If you are a scientist yourself or just an inquisitive person, and you often watch or read last news in the field of science or technology. It is for you that we have created such a section, which covers the latest world news in the field of new scientific discoveries, achievements, as well as in the field of technology. Only the latest events and only verified sources.

In our progressive times, science moves at a fast pace, so it is not always possible to keep up with them. Some old dogmas are crumbling, some new ones are being put forward. Humanity does not stand still and should not stand still, and the engine of humanity is scientists and scientific figures. And at any moment a discovery can occur that can not only amaze the minds of the entire population of the globe, but also radically change our lives.

Medicine plays a special role in science, since man, unfortunately, is not immortal, is fragile and very vulnerable to all kinds of diseases. Many people know that in the Middle Ages people lived on average 30 years, and now 60-80 years. That is, life expectancy has at least doubled. This was, of course, influenced by a combination of factors, but it was medicine that played a major role. And, for sure, 60-80 years is not the limit of an average life for a person. It is quite possible that someday people will step over the 100-year mark. Scientists from all over the world are fighting for this.

Developments are constantly underway in the field of other sciences. Every year, scientists from all over the world make small discoveries, little by little moving humanity forward and improving our lives. Places untouched by man are being explored, primarily, of course, on our home planet. However, work is constantly happening in space.

Among technology, robotics is especially rushing forward. The creation of an ideal intelligent robot is underway. Once upon a time, robots were an element of science fiction and nothing more. But already at this moment some corporations have real robots on their staff that perform various functions and help optimize labor, save resources and perform for a person dangerous species activities.

I would also like to pay special attention to electronic computers, which 50 years ago took up a huge amount of space, were slow and required a whole team of employees to maintain them. And now there is such a machine in almost every home, it is already called more simply and briefly - a computer. Now they are not only compact, but also many times faster than their predecessors, and anyone can understand it. With the advent of the computer, humanity opened a new era, which many call “technological” or “information”.

Remembering about the computer, we should not forget about the creation of the Internet. This also gave a huge result for humanity. This is an inexhaustible source of information, which is now available to almost every person. It connects people from different continents and transmits information at lightning speed, something that would have been impossible to even dream of 100 years ago.

In this section, you will certainly find something interesting, exciting and educational for yourself. Perhaps even someday you will be able to be one of the first to learn about a discovery that will not just change the world, but will change your mind.

A treadmill is one of the most popular exercise machines for training at home. Proper operation of the simulator and compliance with the manufacturer’s recommendations will help avoid breakdowns for a long time. An important role is played by maintaining cleanliness, stable humidity in the room, a flat and hard surface under the simulator, the presence of a special shock-absorbing mat is welcome.

If no manufacturing defect was detected during operation of the treadmill, and the exercise machine was operated in accordance with the manufacturer’s recommendations, then a frequent cause of breakdown is careless handling of the exercise machine, exceeding the permissible recommended weight, improper use, lack of grounding and fluctuations in the power supply voltage. Some errors when operating the treadmill are shown on the display.

Let's look at examples of some problems and ways to solve them:

If the display shows E0, it means that you have not installed the security key. It’s easy to solve this problem; you just need to put it in the appropriate slot on the console.
Error E1 on the console indicates a malfunction of the speed sensor. First, you need to check the contacts of the power cable, turn off and on the power using the button next to the power cable connection socket, and if that doesn’t help, then you need to contact the service department. Often such a mistake is a consequence of exceeding the maximum allowable weight of the athlete. And, if there is no mechanical failure, then try to cure it as described above - turning off/on the power button of the simulator on the back panel of the casing.
If the simulator shows E2, then this means problems with the operation of the engine or electric drive. To solve this problem, you also need to check the cable contacts, turn it off/on and, if that doesn’t help, then contact customer service.
Treadmill with fault code E3 reports over speed. You need to adjust the speed sensor yourself, but it is best to contact a specialist.
If the problem is that the management console does not turn on, then you need to check the console's power cord. It must be connected correctly until the latch clicks and be in the correct position. Changing the polarity if the wire is connected incorrectly or upside down can lead to the failure of expensive electronics. Do not forget about the treadmill switch on the casing, to which the power wire from the outlet is connected, it must be set to “ON”.
If during training the treadmill belt stops moving, then you need to get off the treadmill and check its functionality while standing on the floor, in order to avoid injuries caused by a sudden and unexpected start of the treadmill belt. If the voltage in the network is stable, there are no extraneous sounds or smell of burnt plastic, and the wire is securely inserted into the plug and socket of the simulator casing, and rebooting the system did not help, then the problem may be caused by insufficient voltage in the network, which can be caused by big amount electricity consumers connected to the network or using a household extension cord. The solution to this problem is to turn off unnecessary devices and refuse to use the treadmill extension, choosing a different place for training.
If the running belt of a treadmill moves relative to the center during operation, then you need to check the floor, make sure that the machine is placed on a flat surface, and that the running belt is tensioned correctly and evenly. For detailed information in this case, you need to study in detail such a section of the simulator instructions as adjusting the running belt.

During operation, do not forget to periodically lubricate the back of the running belt in accordance with the manufacturer’s recommendations from the machine’s data sheet. Damage to the integrity of the simulator deck coating caused by debris getting under the belt will be aggravated by the lack of lubrication and can lead to damage to the deck and belt, followed by costly repairs.

Proper maintenance of exercise equipment at home.

The cause of most breakdowns sports equipment, is non-compliance with operating rules and lack of timely maintenance of simulators. Preventing a disease is easier than treating it, and this applies not only to human health, but also to breakdowns of exercise equipment.

Compliance simple rules equipment maintenance will save you money:

Each exercise machine is designed for a certain user weight and continuous operation time. Read the manufacturer's recommendations in the instructions.
Lubrication of moving parts prevents premature wear of parts. Initially, the simulator is already lubricated, but over time the oils dry out, which leads to deformation and destruction. It is recommended to check and, if necessary, lubricate the main components of the simulators at least once every three months. For exercise bikes and orbitreks, it is necessary to check the presence of lubrication on all axes. Treadmills are lubricated with silicone oil under the belt.
Room temperature and humidity. One of the reasons for breakdowns of the simulator is excessive humidity and high/low air temperatures. This leads to drying out of the drive belts, metal corrosion and electronic failure. Strictly follow the manufacturer's recommendations. For example, you should not place the exercise machine in damp areas of basements, or on an unglazed balcony.
If noise, creaking or loose parts of the simulator appear, it is necessary to promptly find the cause and eliminate it. Otherwise it will cause damage.
Maintenance of the battery compartment of the simulator. If your exercise machine model runs on batteries, replace the elements regularly to prevent them from oxidizing in the battery compartment. It is not recommended to use cheap batteries.
Dust is the main enemy of electronics. A common cause of breakdowns of electrical exercise equipment is dust, which accumulates static energy. This is especially true for treadmills. When servicing the machine, do not forget to thoroughly vacuum it and wipe it with a dry towel.
Check the condition of the cables power stations. If you find a partially damaged cable, replace it with a new one to avoid damage to the simulator when the load breaks.
Such simple recommendations will extend the life of your exercise equipment.

Home treadmill repair.

In this article, we will look at the most common treadmill breakdowns and methods for eliminating them.
Sports equipment, like any other mechanism, includes a lot of mechanical and electronic mechanisms that require periodic maintenance and care.

Treadmill repair at home.

In order to repair the simulator yourself, you must have:
A set of suitable tools and equipment
Ability to use the tool
And, of course, technical knowledge of how treadmills work.

The tool kit should include:
Spanners
Hex key set
Flat and figured screwdrivers, different sizes.
Pliers
Multimeter
The above list is minimum set necessary tools, without which you should not start repairing treadmills. There is a lot of information on the Internet about how to use these tools, so we will not focus on this.

Before we begin repairing the treadmill, let's take a closer look at its structure and operating principle.

Any electric treadmill, consists of two sets of mechanisms: mechanical devices and electronic (electric). Mechanical components include:
The drive belt, which is responsible for transmitting torque from the engine to the shaft.
The front and rear shafts drive the treadmill belt.
The treadmill belt is the main mechanism that allows a person to run in one place at a given speed.
The deck is a board made of synthetic fiber, which is located under the canvas.
Treadmill frame.
The drive motor drives the treadmill belt.
The tilt motor allows you to change the tilt angle of the blade.
Console - control panel.
Power controller - a board that controls the motors.
Let's look at the most common breakdowns and methods for eliminating them:

1. The treadmill does not turn on.
Modern exercise machines are equipped with an automatic fuse that protects against voltage surges. This fuse is made in the form of a button, which is located at the bottom, next to the switch and the power cord. When switched on, the safety button must be pressed in. If such a fuse is missing or is in the on state, you need to check the fuse on the power controller. The power controller is located under the cover, at the front bottom of the machine.
2. The treadmill turns off while running.
Such problems are most often associated with worn brushes of the drive motor, or an over-tensioned blade. If the brushes are weakly pressed against the commutator contacts, then it’s time to change them. Check the tension of the canvas; you need to lift the left or right edge up with your hand; if the canvas does not rise more than a couple of centimeters, then it is too tight. With normal tension of the canvas, it rises to 10-15 centimeters.
3. The treadmill starts and immediately turns off.
In 99% of cases, this is due to a failure of the reed relay or a magnet falling out of the engine flywheel. Often, during improper transportation, the magnet simply falls out of the flywheel.
4. The canvas has moved to the side.
To eliminate this problem, it is necessary to adjust the position of the rear shaft vertically, so that the web is tensioned evenly along the entire length of the shaft.
5. While running, the belt slips.
During operation, the canvas stretches, which leads to a weakening of its tension. It's quite simple to tighten the rear shaft.
6. Knocking while running.
As a rule, such breakdowns are associated with wear of the engine bearings or shaft.
7. The console starts at startup, but the engine does not work.
Most often, the cause of such breakdowns is the failure of the motor power controller.

Our article is not about the mistakes that runners make, but about the main types of failures in the operation of home cardio equipment.

Failures are usually identified by an alphanumeric identification code. When something is wrong with the mechanism, a code is displayed on the on-board computer display.

How to understand what the problem is?

The letter "E" stands for "error". In combination with numbers signaling a problem, this is what is most often used.

Here are the main signals of problems.

Treadmill Error Codes

E-0- safety signal; for some reason the key does not work - it is either not connected to the console or is broken. Check that the connection is correct. If you have done everything as you should and the error persists, clean your console.

E-1- the reed speed sensor is faulty; it does not receive a signal. In most cases, breakdown occurs as a result of inaccurate movement of the simulator (the sensor reacts to a magnet fixed in the flywheel, and the magnet can move from a sharp push). You need to open the engine compartment and adjust the magnet. It also happens, however, that the sensor itself breaks down - it has to be replaced.

E-2- the motor is not in order. Possible explanations for the failure are breaks, winding defects, failure of the control controller. We strongly do not recommend that you resolve the E-2 error yourself; it is better to contact a service center. The engine contains explosive components.

E-3- the track tape does not move at the speed requested by the user. The malfunction is very common. It is caused by damage both purely mechanical and related to the operation of the electric motor. Make sure the deck (the board underneath the canvas) is intact and level. Lubricate the track - see If you are friendly with technology, evaluate the serviceability of the bearings. A burning smell indicates a motor defect.

Attention: the numerical designations of errors on individual track models differ from the standard ones. To avoid confusion, find the “native” instructions for the device.

Soberly assess your strengths. If you break a device that is still under warranty, you will deprive yourself of the right to receive free professional help.

Owning a treadmill is excellent option for training, maintaining your own body in normal condition.

At the same time, you need to take care not only of your own body, but also of the simulator. If you know how to do this, the track will last longer and perform better.

And if it begins to show malfunctions or simply stops working, this article will be very useful to you before contacting a specialist.

Cleaning the path

The treadmill belt will become dirty over time: sweat falls here, and shoes also cause some contamination. If you do not clean it regularly, the canvas will become unusable.

In fact, cleaning a treadmill is quite simple and for this you only need two items:

• rag– it is best to use rags that are specially designed for wet cleaning and normally absorb moisture;
• vacuum cleaner– It is best to use a normal, powerful vacuum cleaner with various attachments.

After each workout, you should wipe the machine with a cloth (in particular the console and the canvas). Use only clean water and a slightly damp cloth.

You can not use a vacuum cleaner every day, but from time to time vacuum around the perimeter of the exercise machine and in the spaces between the canvas and the frame. The canvas needs to be washed and vacuumed, gradually turning it. Periodically remove the engine cover and clean the engine from dust and other contaminants.

Carefully! Do not use soap or similar cleaning products on either the treadmill or the belt. Before cleaning, you must unplug the device from the outlet.

Maintenance of the running belt - 4 steps

It must first be study the instructions, which describe the placement of tension bolts exactly in your model. It may also indicate how to properly tension and level the running belt so that it does not move out. The simulator must be maintained regardless of

It won’t hurt to familiarize yourself with the material if you are not yet knowledgeable enough about this issue.

1. Pull-up

In general, the process of tightening the canvas is very simple:

1. turn on the track at a speed of less than 4 km/h;
2. Find out from the instructions where the tension bolts are located on the back of the blade;
3. use special key, which is included in the simulator kit;
4. for minimal tightening you need to make a quarter turn clockwise;
5. you need to tighten both bolts by an identical number of turns;
6. if you want to loosen the blade, turn the keys in a different direction.

Important! You should correctly determine the tension of the belt; here you need to not overtighten: excessive tension can break the front rollers of the track. Therefore, you always need to correct it smoothly and evenly.

2. Centering

In fact this process is not significantly different from the previous one: You just need to rotate the keys in different directions.

So, first you need to get off the track and turn on the speed of about 5 km/h, after that:

1. look at which direction the canvas is shifted;
2. shift to the left side - turn the left bolt to the right side a quarter turn, then turn the right bolt to the left side a quarter turn;
3. shift to the right side - do the opposite: that is, rotate the right bolt clockwise, a quarter turn, and rotate the left bolt counterclockwise, a quarter turn;
4. check the alignment of the blade, you can do this at increased speed;
5. if the blade needs to be trimmed, reduce the speed and repeat the steps for using the keys, trim smoothly a quarter turn on each side.

This algorithm will help you level the canvas. Typically, allen keys are used for treadmills.

For proper centering and tensioning use a simple visual method. The track surface should be raised approximately in the middle. The optimal gap is from 5 to 7 centimeters: if less, you need to loosen the tension, if more, tighten it.

3. Heating, wear and replacement of the blade

If the running belt gets hot, the problem may be excessive friction and need for lubrication. Should the canvas be heated? We’ll talk about this in more detail later.

The running belt will wear out over time and you will need to replace this element. Timely replacement of the running belt will increase the life of the deck treadmill and will avoid frequent repairs. To find out when to change the blade, you should use a simple feeling method.

Note! The canvas rises in the center, and you feel the inside with your hand. If you observe something like a torn surface, then it needs to be changed. This fact should be checked every 10-12 weeks. The condition of the special orthopedic fabric should be checked even more often

In addition, you may feel wear on the blade: slipping or periodic slowdown when increasing speed or stepping on the blade. Also, worn-out fabric accumulates static electricity on the simulator. If you feel static discharge, then the problem is either static in the fabric or in the processor on the control board.

As a rule, the width of the running belt in diameter is 40 or 51 centimeters, and the length is from 110 to 150 centimeters. One way or another, you can always find out the size of your canvas in the instructions.

To correctly change the canvas, you will need special experience and skills. That's why We will not advise you how to replace the blade yourself for the first time. In many stores that sell treadmills, you can order the services of treadmill maintenance technicians. Hire such a specialist and watch how a professional changes and adjusts the canvas.

In the future, you can try to perform this process yourself, but it is better to use the services of specialists. Moreover, this process will require about an hour of your time, and improper installation will result in a decrease in performance characteristics.

4. Lubrication

To reduce wear on parts and extend the service life, the track will need to be lubricated regularly. The lubricant creates a layer between the blade and the deck, due to which the belts and engine wear out less, the coefficient of friction is reduced and, accordingly, the load is reduced.

Each treadmill has different lubrication needs, and it is best to focus on the intensity of use. For example, some manufacturers advise updating the lubricant every 300 kilometers of use or every 30 hours of use. If the treadmill squeaks when running, then you need to urgently lubricate it and show it to a specialist.

However, there is a more accurate method for determining how often to lubricate. To do this, follow these steps:

1. stop the track;
2. lift the canvas;
3. slide your finger under the canvas;
4. dry blade – lubrication is needed;
5. feels like silicone grease - no lubrication required.

Attention! require even more frequent lubrication, since they have a greater load on the blade. Nevertheless, you should not neglect lubrication of the tracks either.

Now you need to decide on the type of lubricant, and here you should strongly advise do not use unprofessional mixtures. For example, if you do not want to purchase a new exercise machine, the thought of using industrial oil or a similar mixture should be completely discarded. The best option is always oil-free silicone spray lubricants, which perform two main tasks:

• lubricant;
• separating agent.

As a rule, both of these functions are indicated on a can of normal mixture, and these are the options you should prefer. If you don’t know what to lubricate, pay attention to the manufacturers Hasttings and Efele, which have proven themselves to be excellent. You can also take a closer look at Molykote Separator Spray.

One way or another, you will need an option with a silicone base, which may contain a hydrocarbon propellant. Now the most convenient form of release is aerosol lubricants, but there may be other options.

Actually the process consists of such actions:

1. disabling the track;
2. raising the canvas on one side;
3. applying lubricant - between the deck and the seal, apply small splashes of lubricant over the entire surface;
4. raising the canvas on the other side;
5. applying lubricant;
6. turn on the treadmill for 3-5 minutes at low speed;
7. at low speed;
8. After this, the lubricant will be evenly distributed over the surface.

Attention! Find out if the deck of your simulator does not use a paraffin layer, then lubrication with silicone mixtures is not required.

Where can I put the exercise machine?

Either way, you will need a treadmill mat that absorbs vibrations and noise during use. A special rug will not only help you get rid of noise and not disturb your neighbors, but also keep the material safe.

Can the exercise machine be placed on carpet, laminate, linoleum or parquet? In fact, you can completely use a path on these surfaces, the main thing is use a special mat. If one is not used, then a simple carpet will become wrinkled over time. The same applies to laminate.

Is it possible to put a path on the balcony? If you want to install the exercise machine on the balcony, then this is only possible if there is insulation. The simulator electronics will work worse if the temperature often drops below +10 degrees. If you have little space, initially opt for

5 most common malfunctions

In order for the simulator to work properly, it is best to use service from professionals, although you can solve some problems yourself.

1. Doesn't turn on. The electronic console may be damaged by power surges. Therefore, for treadmill maintenance, you should always use a separate circuit and a grounded AC outlet. The motor or power controller may have burned out.
2. The canvas is slipping. Perhaps the issue is the wear and tear of the deck or canvas. Blade tension and evenness may require lubrication or adjustment.
3. Turns off involuntarily. Overload protection may be activated. Sometimes the problem may be a power outage; try using a voltage stabilizer. Find out the maximum weight allowable for your treadmill.
4. Twitches. This can often occur due to wear on the running belt or deck, or the treadmill rollers are small in diameter and worn out.
5. The console doesn't work. Most often, there is no electrical contact in some console connectors or harnesses. During the warranty period, the console can be easily replaced without any difficulties.

Attention! If you observe any problems that may be electrical related, try simply turning off the power supply and turning it back on after 15 minutes. Some problems with electronic boards can be corrected simply by turning them off.

Be sure to correct all faults in a timely manner - this is required

Error messages (E) on screen

On the treadmill screen you can observe various error options, which are marked with the letter E. As a rule, the standard classification is used, but Error numbering may vary depending on manufacturer and model.

• There is no information on the screen. You should check the button to turn on the console, as well as the power cord and power switches. The overload protection system may be working, then you just need to wait a little and the track will turn on again. In addition, you should look at the wiring harnesses, connections and connectors.
• E-1, connection error. There may be defective wires that require replacement. We check the serviceability of the connectors, console and controller wires.
• E-2, voltage mismatch in the network. The reason may be a malfunction of the engine, or the voltage in the network may actually change by 30-50%, after which the track automatically turns off. Sometimes there is poor contact in the engine circuit, you should check the engine compartment, connectors and wires.
• E-3, signal from the walking belt motion sensor. You need to check the magnet attached to the pulley or the motion sensor itself.
• E-4 and E-6, inclination of the running belt. The malfunction may be in the tilt motor. It is advisable to check the wires in the voltage regulator and tilt motor. In addition, look at the wires and connectors of the console and power board controllers.
• E-5, reboot protection. A very useful solution here is to turn off the network and turn on again after 15 minutes. Pay attention to the user's weight: as a rule, manufacturers slightly overestimate the maximum characteristics, so tracks should always be taken with a safety margin of 20-30% more than your parameters. If the user's weight exceeds the possible weight, this error may appear. The cause may also be wear on the engine or the track surface.
• E-7, electrical part of the controllers. The cause may be a faulty connector, current transformer or defective wires. Check the wires that go from the machine computer to the lower power control board.
• E-8, drive control. The drive itself may be faulty. Also check the tension in the drive poly V-belt.
• E-9, position. Either the drive is faulty, or the simulator needs to be unfolded and restarted.
• E-10, engine. Look at the wires that connect the console and controller. If the engine does not turn on, does not rotate or jerks, the reason is the magnetic key, you need to check it; if the problem persists, the console may need to be replaced.

It turns out you need to know not only how to use the simulator, but also how to properly care for it.

As you can see, a significant portion of errors occur due to faulty connectors or wires in one part of the path or another. More expensive models are usually more durable and wear out more slowly, but a lot depends on the intensity of use of the machine. Often even budget options simulators have very reliable parts.

Monitor the operating conditions and timely prevention of various treadmill malfunctions. Thanks to this, you can significantly save on the purchase of new parts and repair work on the treadmill. Wherein We recommend that you trust professionals more often and do not repair significant problems yourself, especially if you do not have the proper experience in this matter.